Electronic Communications Act, 2005 (Act No. 36 of 2005) ICASA Notice regarding Final Radio Frequency Assignment Plans for the Frequency Band 410 to 430 MHz in terms of Regulation 3 of the Radio Frequency Spectrum Regulations, 2015 Appendices Appendix C

 

Appendix C  -  Coordination for LTE- and CDMA- Systems

 

PREFERENTIAL PHYSICAL-LAYER CELL IDENTITIES (PCI) FOR LTE46 AND CODES FOR CDMA

 

The following is extracted from ECC/REC (11)05 and T/R 25-08 as an operational example and can be adapted for the SADC countries for LTE. A respective extract from ECC/REC (15)01 may be considered for expanding the same onto NR.

 

 

PCI coordination is only needed when channel centre frequencies are aligned independently of the channel bandwidth.

 

3GPP TS 36.21147 defines 168 “unique physical-layer cell-identity groups” in §6.11, numbered 0...167, hereafter called “PCI groups” for LTE. Within each PCI group, there are three separate PCIs giving 504 PCIs in total.

 

Administrations should agree on a repartition of these 504 PCIs on an equitable basis when channel centre frequencies are aligned, as shown in the table below. It has to be noted that dividing the PCI groups or PCIs is equivalent. Each country should only use their own preferential PCIs close to the border and can use all PCIs away from the border. This transition distance between “close to the border” and “away from the border” should be agreed between neighbouring countries.

 

Administrations may wish to define different field strength levels (than those provided in the main text referring to this Appendix) for non-preferential PCIs.

 

As shown in the table below, the PCIs should be divided into 6 sub-sets containing each one sixth of the available PCIs. Each country is allocated three sets (half of the PCIs) in a bilateral case and two sets (one third of the PCIs) in a trilateral case.

 

Four types of countries are defined in a way such that no country will use the same code set as any one of its neighbours. The following lists describe a sample distribution for African countries:

 

Country type 1: Botswana, Cameroon, Comoros, Democratic Republic of the Congo, Ghana, Guinea- Bissau, Kenya, Liberia, Malawi, Mauritius, Niger, Republic of the Sudan, Swaziland;

 

Country type 2: Algeria, Angola, Benin, Cape Verde, Chad, Cote d'Ivoire, Egypt, Ethiopia, Madagascar, Senegal, United Republic of Tanzania, Zimbabwe;

 

Country type 3: Burkina Faso, Congo, Djibouti, Equatorial Guinea, Guinea, Mauritania, Nigeria, Rwanda, Sao Tome and Principe, Seychelles, South Africa, South Sudan, Tunisia, Zambia;

 

Country type 4: Burundi, Central African Republic, Eritrea, Gabon, Gambia, Lesotho, Libyan Arab Jamahiriya, Mali, Morocco, Mozambique, Namibia, Sierra Leone, Somalia, Togo, Uganda.

 

(Note: A sample country type map can be found in the figure below).

 

For each type of country, the following tables and figure describe the sharing of the PCIs with its neighbouring countries, with the following conventions of writing:

 

 

Notes

 

 

 

For code coordination each base station shall use a unique time offset of the pilot pseudo-noise (PN) sequence to identify a Forward CDMA Channel. Time offsets may be reused within a CDMA cellular system. Distinct pilot channels shall be identified by an offset index (0 through 511 inclusive). This offset index specifies the offset time from the zero-offset pilot PN sequence in multiples of 64 chips. The same pilot PN sequence offset shall be used on all CDMA frequency assignments for a given base station. To distinct signals with PN sequence offsets all base stations should be time synchronised, but such synchronisation is mandatory requirement for CDMA2000 standard.

 

Administrations should agree on a repartition of these offset indexes on an equitable basis. Each country should only use its own codes close to the border.

 

In border areas, codes will be divided into 6 "index sets" containing each one sixth of the available offset indexes. Each country is allocated three index sets (half of the indexes) in a bilateral case, and two index sets (one third of the indexes) in a trilateral case.

 

Four types of countries are defined in such a way that no country will use the same index set as any one of its neighbours. The following lists describe a sample distribution for African countries:

 

Country type 1: Botswana, Cameroon, Comoros, Democratic Republic of the Congo, Ghana, Guinea- Bissau, Kenya, Liberia, Malawi, Mauritius, Niger, Republic of the Sudan, Swaziland;

 

Country type 2: Algeria, Angola, Benin, Cape Verde, Chad, Cote d'Ivoire, Egypt, Ethiopia, Madagascar, Senegal, United Republic of Tanzania, Zimbabwe;

 

Country type 3: Burkina Faso, Congo, Djibouti, Equatorial Guinea, Guinea, Mauritania, Nigeria, Rwanda, Sao Tome and Principe, Seychelles, South Africa, South Sudan, Tunisia, Zambia;

 

Country type 4: Burundi, Central African Republic, Eritrea, Gabon, Gambia, Lesotho, Libyan Arab Jamahiriya, Mali, Morocco, Mozambique, Namibia, Sierra Leone, Somalia, Togo, Uganda.

 

For each type of country, the following tables and figure describe the sharing of the indexes with its neighbouring countries, with the following conventions of writing:

 

 

Because of the time shifting mechanism for code generation, the situation can appear that propagation delay may lead to the synchronisation of two different base stations signals occurring in some parts of the service area. The average diameter of such correlation areas could be up to 245 meters (one chip duration multiplied on light speed). To prevent such situations in border areas it is recommended not to use some codes and to introduce 4 exclusion codes between neighbouring index sets what gives 78.125 km propagation path before a possible correlation area appears. This precludes any real synchronisation and will not affect network planning, causing a reduction of code space less than on 5% only in border areas.

 

Code sharing between two countries should be applied or used by base stations that exceed the relevant trigger level of only one neighbouring country. Code sharing between three countries should be applied or used by base stations that exceed the relevant trigger level of two neighbouring countries.

 

Notes

 

 

 

 

 

 

The decision of which of these methods to use in cross-border coordination should be agreed upon by the interested parties. Specific DM RS sequence groups or hopping patterns repartition is not provided in this text but could be deduced in a similar manner to the PCI repartition.

 

 

Another radio network parameter that is considered during radio network planning is PRACH configuration which is needed to distinguish random access requests addressed to different cells. PRACH resources are allocated by specifying the PRACH Resource Blocks time positions within the uplink frame, their frequency position within the LTE channel bandwidth and by apportioning cell-specific root sequences. During radio network planning, these parameters are usually used in the following way:

 

 

For cross-border coordination, it is proposed to use frequency position offsets to exclude the possibility of so-called “ghost” PRACH requests caused by neighbouring networks. The PRACH is configured in LTE to use only 6 Resource Blocks or 1.08 MHz of the LTE channel bandwidth except in regions used by PUCCH. In case of overlapping or partially overlapping channel bandwidths of neighbouring networks, it is enough to establish non-overlapping PRACH frequency blocks to perform coordination. Because it is difficult to establish an implementation dependent procedure for such allocation, it will be the responsibility of operators to manage such frequency separation during coordination discussions.

 

In an early implementation, it is possible that a very limited number of frequency positions could be supported by LTE equipment which will not be enough to coordinate in the trilateral case. In such cases, root-sequence repartition could be used. There are 838 root sequences in total to be distributed between cells, numbered {0..837}. There are two numbering schemes for PRACH root sequences (physical and logical) and that only logical root sequences numbering needs to be used for coordination. Unfortunately, the process of root sequences planning doesn’t involve direct mapping of root sequences between cells because the number of root sequences needed for one cell is dependent on the cell range. The table showing such interdependency is presented below:

 

 

Thus, in the case of root sequence reparation, it will be the responsibility of radio network planners to assign the correct number of root sequences in order to not overlap with the root sequence ranges of other operators. It also should be noted that different root sequences have different cubic metrics and correlation properties, which affect PRACH coverage performance and planning of so-called high-speed cells. For simplicity of cross-border coordination, it is proposed to ignore these properties.

 

In summary, it should be stipulated that frequency separation of PRACH resources should be used as the main coordination method. PRACH root sequences repartition should be avoided and used only in exceptional cases. Specific PRACH root sequences repartition is not provided in this text but could be deduced in a similar manner to the PCI repartition.

 

Additional guidance for cross-border coordination of synchronised and unsynchronised LTE and 5G/NR TDD systems may be found in ECC/REC/ (15)01 (48) and ECC Report 296 (49).

 

Additional guidance on border code coordination between CDMA systems and additional information on coordination thresholds may be found in ECC Report 108 50.

 

_________________________________________